Energy monitoring and telemetry for industrial plants and utilities

Technician in a plant room with a tablet showing consumption, next to a panel with CrystalBox
Energy efficiency and Industry 5.0

Consumption measured. Savings documented.

CrystalBox reads the power analysers and meters you already have and brings electricity, water and gas consumption to the cloud. Your switchboards stay as they are.

Technician in a pumping station checking data on a tablet, with a CrystalSpot probe on the pipe and a CrystalBox on the panel
Telemetry and remote monitoring

Every reading in your plant, under remote control.

Cold rooms, tanks, pumping stations, greenhouses: every plant under remote control, with the sensors you already have or with battery-powered wireless probes.

Installer wiring a CrystalBox into an electrical panel with a laptop beside him
System integrators and OEMs

Remote monitoring to offer your customers.

Ready-made gateways, wireless probes and a multi-customer cloud: install and configure from a browser, without developing electronics or firmware.

The solutions in detail

The same system, set up differently: to measure and document energy use, to watch a plant remotely, or to offer monitoring to your own customers.

CrystalCloud dashboard with monthly consumption, year-on-year comparison and energy KPIs Consumption and savings in CrystalCloud

Measure consumption and prove the savings

ESCOs, energy managers and consultants need to measure consumption for energy audits and document the savings. CrystalBox reads the meters already installed and sends the data to the cloud in 15-minute detail: no intermediate concentrators, no switchboards to replace, no machines to stop.

  • Power analysers over Modbus RTU or TCP, and gas, water and thermal energy meters with Modbus or pulse outputs
  • Measuring points organised into main activities, auxiliary services and general services, as in the ENEA monitoring plan
  • Energy performance indicators (EnPI): specific consumption compared with the baseline and the sector benchmark
  • Machine interconnection and remote monitoring, among the technical requirements for Italian tax incentives
  • Year-on-year comparison and PDF reports to document the savings achieved
  1. 1SurveyWith your consultant, choose the measuring points; we check how to read each instrument
  2. 2ConnectCrystalBox arrives pre-configured: it connects to the RS485 bus, the network or the pulse outputs
  3. 3ReportConsumption, EnPI and reports in CrystalCloud

YDEA provides measurements and analysis tools: the energy audit and the certification of savings remain with your consultant or assessor. Readings are for monitoring, not for billing. Incentive rates and requirements depend on the regulations in force.

How it works: from sensors to the cloud, without rebuilding the plant

Gateway, probes and cloud are designed in-house by YDEA to work together. Start with one measuring point and grow one sensor at a time.

  1. Collects

    4–20 mA sensors, PT100/PT1000 probes, digital contacts, instruments and PLCs over Modbus RTU/TCP. Where cables can't reach, battery-powered wireless probes.

  2. Transmits

    Sends the data to the cloud over Wi-Fi, Ethernet or 4G. If the connection drops, it keeps them and sends them when it's back.

  3. Watches

    Thresholds on every reading, with trip and reset delays. When a value goes out of range, an alarm arrives by email.

  4. Shows and stores

    Dashboards, site maps, history and period comparisons in CrystalCloud, on PC, tablet and smartphone, with users and role-based permissions.

CrystalBox inputs

Each input is set from the gateway's web page: choose what to connect, without changing hardware.

A1A2A3A4
Analogue inputs4–20 mA, PT100/PT1000 or contact, with thresholds and delays
P1P2
Serial portsIsolated RS485 to instruments and PLCs over Modbus RTU
RF
Radio 868 MHzUp to 15 battery CrystalSpot probes
Wi-FiLAN4G
NetworkTo the cloud; LAN also does Modbus TCP

Modular. Start with one measuring point and add probes and plug-ins when needed.

Wired and wireless together. Gateway inputs and radio probes in the same installation.

On the plant you already have. It reads the instruments, meters and PLCs already installed: your panels stay as they are.

Crystal System in 80 seconds

The gateway, the wireless probes and the cloud platform, in the studio and at work: switchboards, boiler rooms, cold rooms and pumping stations.

The three components

Start with one gateway and a few probes; add plug-in modules and new measuring points when you need them, without redoing the installation.

GatewayCrystalBox gateway

CrystalBox

Modular multi-interface concentrator for wired and wireless field data.

  • 15 probesCrystalSpot wireless
  • 4 inputs4–20 mA, PT100/PT1000, contacts
  • 2 serial portsisolated RS485
  • Wi-Fi, LAN, 4Gto the cloud
Technical specifications
Wireless probes
Up to 15 CrystalSpot, linked by 868 MHz radio
Analogue inputs
4, each configurable as 4–20 mA (powered by CrystalBox at 24 VDC or in series with an existing loop), PT100/PT1000 probe or dry contact; 16-bit conversion
Serial ports
2, galvanically isolated 2- or 4-wire RS485 with selectable bus termination and biasing; for instruments and PLCs over Modbus RTU/ASCII
Pulse inputs
With the Encoder plug-in: 3 optoisolated inputs per module, up to 6 with two modules, for pulse-output meters (dry contact, open collector) and encoders
Connectivity
Built-in 2.4 GHz Wi-Fi; 10/100 Ethernet (including Modbus TCP master/slave) and 4G/LTE via plug-ins
Set-up
From the built-in web page, locally or remotely
Memory
Internal data memory: if the connection drops, readings are kept and sent when the line returns
Power
5 VDC via USB-C, power supply and cable included; about 2 W consumption
Size
120 × 120 × 40 mm; IP20 rating, for indoor or cabinet installation; operating temperature 0 to +50 °C
Mounting
Wall or magnetic mounting; multicolour status LEDs
Wireless probeCrystalSpot wireless probe with e-paper display and probe terminal block

CrystalSpot

Battery-powered sensor node for measuring points that are hard to wire.

  • PT100/1000temperature
  • 4–20 mAlevel and pressure
  • 868 MHzlong-range radio
  • e‑paperon-site reading
Technical specifications
Versions
Temperature with PT100/PT1000 probe; temperature and humidity; 4–20 mA input for level and pressure; contact for states and alarms
Plug-in modules
Takes the same input modules as CrystalBox: one kind of module to stock for both
Display
E-paper: the reading is visible on site and the display uses no battery to stay on
Power
2 replaceable LS14500 3.6 V lithium cells; estimated life of over a year with one reading per minute; the interval is adjustable and longer intervals extend battery life
Radio
868 MHz, long range and low power
Size
80 × 80 × 40 mm; IP20 rating, for indoor use; operating temperature 0 to +50 °C (in sub-zero rooms only the probe goes inside)
Installation
No wiring: the probe pairs with CrystalBox by radio and gets its configuration from it
Web platformCrystalCloud on laptop and smartphone with a map of sites

CrystalCloud

Remote monitoring, alarms and data analysis for all your sites.

  • DashboardsKPIs and maps
  • Alarmsthresholds and email alerts
  • Historycomparisons and reports
  • Encryptedoutbound only
Technical specifications
Interface
Custom dashboards, KPIs, interactive maps; on PC, tablet and smartphone
Structure
Sites, areas and measuring points; each area is classed as main activity, auxiliary service or general service
Energy
EnPI against baseline and benchmark, ranking of the biggest consumers, year-on-year comparison
Alarms
Thresholds on every reading, email alerts
Users
Administrator and read-only operator profiles; each organisation sees only its own sites
Data
History as chart and table, period comparison, PDF reports
Security
Encrypted, outbound-only transmission with no inbound firewall ports to open; automatic backups
Plug-in modulesthe same modules for CrystalBox and CrystalSpot
Analog2 channels: 4–20 mA with 24 V sensor supply, PT100/PT1000, contacts
SerialRS485 2/4-wire, isolated
Encoder3 optoisolated pulse inputs per module, for meters and encoders
LAN10/100 Ethernet, Modbus TCP master/slave; CrystalBox only
LTE4G for sites with no fixed network; CrystalBox only

Frequently asked questions

Can't find the answer? Ask Mr.Tree, our virtual assistant, or write to our engineers.

Can I install the system without a programmer?

Yes. CrystalBox is set up from a built-in web page, like a router: network, probes, inputs and Modbus registers are configured from a browser, locally or remotely.

Which sensors and devices can I connect?

4–20 mA sensors (pressure, level, flow), PT100/PT1000 temperature probes, digital contacts and any device that speaks Modbus RTU (RS485) or Modbus TCP: power analysers such as Electrex, Schneider Electric and Siemens, PLCs and inverters. For proprietary protocols we run a compatibility test first.

What happens if the internet connection drops?

CrystalBox keeps collecting data and stores it locally; when the connection returns, the history is sent to the cloud. Where there is no fixed network, use the LTE module.

Can I set thresholds and alarms?

Yes. On every reading (for example inputs A1…A4) you set thresholds with trip and reset delays, so a momentary spike doesn't trigger an alarm. When a threshold is crossed you get an email alert and the event stays in the history.

What does the IT department need to provide?

A network socket or Wi-Fi with internet access, with a DHCP or static address. CrystalBox transmits encrypted and outbound only: no inbound firewall ports are opened and it can be isolated on a dedicated VLAN. Where the company network isn't available, use the LTE module.

Can the readings be used for an energy audit?

Yes, as monitoring data: 15-minute readings organised by ENEA area, available to the consultant who carries out the audit. YDEA is not a certification body and the readings have no billing value: billing relies on the fiscal meters.

Let's discuss your project

Tell us what you need to measure and where: we'll reply with the right configuration and a quote.

YDEA was founded on its partners' experience in industrial automation, home automation and medical devices. Devices, firmware and software are designed in-house: one partner, from probe to cloud.

Request a quote

Fields marked * are required. We reply within one working day.

Enter your name.
Enter a valid email address.
Write a few lines about your project.
Your email app will open with the message ready to send.